Wire Shelf Dividers — Prevents Goods from Falling

L: 350/400/450/500mm

Core Advantages

    Fall prevention function – Dividers stand vertically on the shelf surface with heights ranging from 80 to 150 mm, creating a physical barrier. When products tip over or are compressed, the divider blocks them from rolling off the shelf front or side edges. Suitable for round products (beverage bottles, cans) and small-dimension boxed items.

    Length specification matching – Four lengths correspond to different shelf depths. Divider length should equal or be slightly less than the shelf panel depth (front-to-back direction). 350 mm for 350 mm depth shelves; 400 mm for 400 mm; 450 mm for 450 mm; 500 mm for 500 mm. After installation, the divider front should be flush with or inset 5 to 10 mm from the shelf front edge.

    Mesh foot fixing – 2 to 4 feet at the base, foot length 15 to 25 mm, compatible with wire mesh shelves (mesh hole diameter 5 to 10 mm, wire diameter 2.0 to 3.5 mm). Insert feet into mesh holes and press down to secure. For removal, lift the divider upward.

    Structural rigidity – Wire diameter: 3.0 to 4.5 mm. Frame edges reinforced with thicker wire or flat bar. Resistance to bending deformation under lateral thrust meets daily use requirements.

Product Features

    Material – Carbon steel wire, diameter options: 3.0, 3.5, 4.0, 4.5 mm. Frame edge material: same diameter or reinforced to 5.0 mm.

    Length options – 350, 400, 450, 500 mm (total horizontal length of divider).

    Height options – 80, 100, 120, 150 mm.

    Width (thickness) – 5 to 10 mm (single-layer construction).

    Mesh pattern – Vertical wire spacing: 25 to 50 mm. Horizontal wire spacing: 50 to 100 mm.

    Surface finish – Electrostatic powder coating (black, white, gray) or hot-dip galvanizing.

    Foot specifications – Quantity: 2 to 4 feet. Foot length options: 15, 20, 25 mm. Foot diameter: 3.0 to 4.0 mm.

    Compatible shelf type – Wire mesh shelves (hole diameter 5 to 10 mm, wire diameter 2.0 to 3.5 mm).

    Lateral load capacity – Permanent deflection less than 2 mm when a 50 Newton force (approx. 5 kg force) is applied to the center of the divider.

    Coverage capacity per divider – Divides a shelf into 2 to 3 independent zones when used with multiple dividers.

    Accessory options – Label holder (clips to front or top of divider), rubber end caps (covers sharp corners), extended feet (for thick mesh shelves).

Application Scenarios

    Bottled water, carbonated beverage, and juice category separation in supermarket beverage sections.

    Canned coffee and energy drink division in convenience store coolers.

    Hardware parts bins and small accessory sorting on warehouse shelving.

    Canned goods and spice bottle organization in home storage cabinets.

    Medicine box and supplement bottle categorization on pharmacy shelves.

Frequently Asked Questions and Precautions

Frequently Asked Questions

Q: Can dividers completely prevent products from falling off the shelf?
A: Dividers block products from rolling off the shelf edge when subjected to external forces (customer loading/unloading, other products tipping over). They cannot completely prevent the intentional pushing of products. Taller dividers provide stronger fall prevention. Select divider height at 50% to 70% of product height.

Q: Are mesh foot-type dividers compatible with all wire mesh shelves?
A: Mesh feet fit shelves with mesh hole diameters of 5 to 10 mm and wire thickness of 2.0 to 3.5 mm. Some heavy-duty shelves have larger holes (15 to 20 mm) or thicker wire (4.0 mm+), where standard feet may not secure. For such shelves, custom longer feet (30 to 40 mm) or alternative fixing methods are recommended.

Q: Do dividers loosen or rotate after installation?
A: With two or more feet inserted into mesh holes, the divider is constrained horizontally and does not rotate. Vertically, gravity and product pressure, combined with friction between the feet and the mesh holes, keep the divider fixed. In high-traffic areas, inspect foot engagement every 3 months. If loosening occurs, slightly bend the foot angle to increase the interference fit.

Precautions

    Before installation, confirm the divider length matches the shelf depth. Dividers that are too short (30 mm+ shorter than shelf depth) create a gap between the divider rear and shelf back wall, allowing products to roll off from the rear.

    Install dividers perpendicular to the shelf front edge, parallel to the edge. Angled installation creates inconsistent zone widths and may allow divider movement.

    Align the divider vertically over the mesh holes and insert the feet fully until the foot base contacts the shelf surface. Incompletely inserted dividers may tilt or detach under load.

    Inspect the divider securing status monthly. Feet may experience plastic deformation over time, reducing clamping force. Replace dividers if looseness is detected.

    Clean with a damp cloth. Avoid high-pressure water jets at the foot-to-mesh contact area, as residual moisture may cause rust.

    The top edge of dividers consists of cut wire ends, which may have burrs. Wear protective gloves when handling or cleaning. Optional rubber end caps cover sharp corners.

    These dividers are not intended for shelves with significant slopes (exceeding 5 degrees), as the gravity component on products may overcome the divider barrier.